Electrical Panel Upgrade and Replacement in Cedar City, UT

Your electrical panel sets the limit on everything else in the building. If you are adding an EV charger, a heat pump, a hot tub or a finished basement, or if the breaker box is decades old, an electrical panel upgrade in Cedar City gives you the capacity and the protection modern loads need.

Call (888) 633-7804Same-day service, 24/7 emergency response

Electrical panel upgrade in Cedar City, UT: what we handle

KITMUND replaces worn-out breaker boxes and fuse boxes and upgrades 100 amp services to 200 amps for homes and businesses in Iron County. We size the new panel with a load calculation, coordinate the disconnect with the utility, and label every circuit clearly before we leave.

200 amp panel upgrade

The standard for modern homes, with room for EV charging, electric heating and cooling, and future circuits.

100 amp to 200 amp upgrade

New meter base, service conductors, grounding and main panel sized for a real load calculation.

Breaker box replacement

Outdated, recalled or damaged panels swapped for a new load center with matching breakers.

Fuse box replacement

Screw-in fuse panels replaced with breakers, plus the grounding and bonding older homes often lack.

Sub panel installation

A feeder and sub panel for a garage, shop, addition, basement or detached building.

Main panel repairs

Burnt bus bars, corroded lugs and loose neutrals corrected, or the panel replaced when repair is not worth it.

Signs you need an electrical panel upgrade in Cedar City

The panel is full and circuits are doubled up on breakers
Breakers trip when the dryer, oven and air conditioning run together
The panel is warm, rusty, buzzing or smells hot
You still have screw-in fuses or a 60 or 100 amp service
You are planning an EV charger, hot tub, addition or all-electric appliances

Why it matters in Cedar City

In Cedar City, cooling is the largest electrical load by far, and many homes also run pool equipment, RV hookups and casitas. We size panels and circuits for peak summer demand in Iron County and use equipment rated for outdoor heat and sun.

For an electrical panel upgrade in Cedar City, call KITMUND at (888) 633-7804. We serve every part of Cedar City, UT and the rest of Iron County.

How our electrical panel upgrade service works in Cedar City

Call (888) 633-7804
Tell us what is happening or what you want installed. We ask a few questions and book a time, or send someone straight away if it is urgent.
We look and explain
The electrician inspects, tests and tells you in plain words what is needed and what it will cost before work starts.
We do the work
Neat, code-correct work with floors and furniture protected. Permits and inspections are arranged where the local jurisdiction requires them.
We test and walk you through it
Everything is tested and labeled, the work area is cleaned, and we show you what was done.

Electrical panel upgrade near me: Cedar City and nearby towns

Our electricians work in every part of Cedar City, including Cross Hollow, Fiddlers Canyon, Three Peaks and Downtown Cedar City. Whether you searched for electrical panel upgrade near Three Peaks or an electrician in Downtown Cedar City, you reach the same crew at the same number. Nearby communities we travel to from Cedar City include Summit (about 12 mi), Kanarraville (about 12 mi), Brian Head (about 13 mi), Parowan (about 17 mi), New Harmony (about 19 mi) and Paragonah (about 22 mi).

Electrical panel upgrade questions in Cedar City

What does an electrical panel upgrade cost in Cedar City?

It depends on the amperage, whether the meter base and service conductors must be replaced, where the panel sits, and what the local utility and building department require. Call (888) 633-7804 and we will look at your panel and give you a written quote for your Cedar City property.

How long is the power off during a panel replacement?

Most residential panel swaps are done in one working day, with power off for part of it. We schedule the utility disconnect ahead of time so you know the window.

Do I need 200 amps?

If you heat or cool with electricity, charge a vehicle at home or plan to add large loads, 200 amps is usually the right size. We run a load calculation so the answer is based on your house, not a guess.

Does a panel upgrade in Cedar City need a permit?

Service changes generally require a permit and inspection from the local jurisdiction. We handle the paperwork and meet the inspector.

More electrician services in Cedar City, UT

People find this service by searching for electrical panel upgrade Cedar City, electrical panel replacement Cedar City, 200 amp panel upgrade Cedar City, 100 amp to 200 amp upgrade Cedar City, breaker box replacement Cedar City, fuse box replacement Cedar City, main panel upgrade Cedar City, sub panel installation Cedar City, electrical panel upgrade cost Cedar City and service upgrade electrician Cedar City.

Talk to an electrician now

Electrical panel upgrade in Cedar City, UT. Call (888) 633-7804 for fast service, 24/7.

Call (888) 633-7804