Call (888) 633-7804

Electrical Panel Upgrade and Replacement in Junction, UT

Your electrical panel sets the limit on everything else in the building. If you are adding an EV charger, a heat pump, a hot tub or a finished basement, or if the breaker box is decades old, an electrical panel upgrade in Junction gives you the capacity and the protection modern loads need.

Call (888) 633-7804Same-day service, 24/7 emergency response

Electrical panel upgrade in Junction, UT: what we handle

KITMUND replaces worn-out breaker boxes and fuse boxes and upgrades 100 amp services to 200 amps for homes and businesses in Piute County. We size the new panel with a load calculation, coordinate the disconnect with the utility, and label every circuit clearly before we leave.

200 amp panel upgrade

The standard for modern homes, with room for EV charging, electric heating and cooling, and future circuits.

100 amp to 200 amp upgrade

New meter base, service conductors, grounding and main panel sized for a real load calculation.

Breaker box replacement

Outdated, recalled or damaged panels swapped for a new load center with matching breakers.

Fuse box replacement

Screw-in fuse panels replaced with breakers, plus the grounding and bonding older homes often lack.

Sub panel installation

A feeder and sub panel for a garage, shop, addition, basement or detached building.

Main panel repairs

Burnt bus bars, corroded lugs and loose neutrals corrected, or the panel replaced when repair is not worth it.

Signs you need an electrical panel upgrade in Junction

  • The panel is full and circuits are doubled up on breakers
  • Breakers trip when the dryer, oven and air conditioning run together
  • The panel is warm, rusty, buzzing or smells hot
  • You still have screw-in fuses or a 60 or 100 amp service
  • You are planning an EV charger, hot tub, addition or all-electric appliances

Why it matters in Junction

Properties near Junction often spread power across several buildings: the house, a shop, a barn, a pump house. Long wire runs need voltage drop calculated, and older rural services are frequently undersized for the equipment added over the years. We design the whole system, not only the new piece.

Ready to book an electrical panel upgrade in Junction? Call (888) 633-7804. A local electrician will answer your questions and set up a visit.

How our electrical panel upgrade service works in Junction

  1. Call (888) 633-7804

    Tell us what is happening or what you want installed. We ask a few questions and book a time, or send someone straight away if it is urgent.

  2. We look and explain

    The electrician inspects, tests and tells you in plain words what is needed and what it will cost before work starts.

  3. We do the work

    Neat, code-correct work with floors and furniture protected. Permits and inspections are arranged where the local jurisdiction requires them.

  4. We test and walk you through it

    Everything is tested and labeled, the work area is cleaned, and we show you what was done.

Electrical panel upgrade near me: Junction and nearby towns

From the center of Junction to the edge of town and beyond, if the address is in Piute County we will come to you. Nearby communities we travel to from Junction include Kingston (about 2 mi), Circleville (about 5 mi), Marysvale (about 14 mi), Antimony (about 15 mi), Greenwich (about 21 mi) and Beaver (about 22 mi).

Electrical panel upgrade questions in Junction

What does an electrical panel upgrade cost in Junction?

It depends on the amperage, whether the meter base and service conductors must be replaced, where the panel sits, and what the local utility and building department require. Call (888) 633-7804 and we will look at your panel and give you a written quote for your Junction property.

How long is the power off during a panel replacement?

Most residential panel swaps are done in one working day, with power off for part of it. We schedule the utility disconnect ahead of time so you know the window.

Do I need 200 amps?

If you heat or cool with electricity, charge a vehicle at home or plan to add large loads, 200 amps is usually the right size. We run a load calculation so the answer is based on your house, not a guess.

Does a panel upgrade in Junction need a permit?

Service changes generally require a permit and inspection from the local jurisdiction. We handle the paperwork and meet the inspector.

More electrician services in Junction, UT

People find this service by searching for electrical panel upgrade Junction, electrical panel replacement Junction, 200 amp panel upgrade Junction, 100 amp to 200 amp upgrade Junction, breaker box replacement Junction, fuse box replacement Junction, main panel upgrade Junction, sub panel installation Junction, electrical panel upgrade cost Junction and service upgrade electrician Junction.

Talk to an electrician now

Electrical panel upgrade in Junction, UT. Call (888) 633-7804 for fast service, 24/7.

Call (888) 633-7804
Call (888) 633-7804, open 24/7